Run flat inserts offered by Polymet are tested to finabel, standards, test, run, in dubai, uae, punctured, combat, off road tire, tyre, military, meeting finebel Agreement, No. A.20.A (20.A.5), FINABEL, Agreement tested on Combat, Tyres, for defence, security, sector, test report, speed, off, road, desert, gravel, road, desert, meeting middle, east, climate, soft sand, burning, desert
Made In UAE –by POLYMET Industries LLC - RAK, a 20 plus year old, proven and trusted manufacturing house of bearing system for bridges, building, metros, and mono rail system, for project in Middle East and other developed countries, has taken up the challenges to manufacture Run Flat inserts for local armoury industries on request to manufacture in UAE. MADE IN UAE .
Cross Country Track - Location UAE Ras AL KHimah Desrt, reverbeds and Camel Tracks - A total distane of 69.14 Km covered in 02:08:16 non stop.Run flat inserts offered by Polymet are tested to finabel, standards, test, run, in dubai, uae, punctured, combat, off road tire, tyre, military, meeting finebel Agreement, No. A.20.A (20.A.5),
“RUNFLAT TIRE INSERTS system” manufactured by POLYMET Industries LLC – RAK are bolted inside the inner center of tire rim, allows to have continued mobility of installed vehicles in emergencies, such as loss of air pressure.
Run Flat inserts also known as RunFlat system are bolted into wheel rim wells and support the tire when flat, absolute zero air, allowing the vehicle to continue driving safely for up to 60km following ballistic or terrain-related tire damage in a cross-country circuit.
Polymet Industries LLC RAK - UAE
Run flat insert system offered by POLYMET were tested repeatedly in grueling desert track of RAK with rubbles, dry crossings, having a number of obstacles such as natural ramps, steps formed in a wadi, ditches as well as gravel tracks with corrugations and loose sand pits – real hostile desert conditions of temperature ranging from 30 C to 50 C in a Loaded Toyota Hilux, loaded above its GVW gross weight of the vehicle.Test Vehicle was diagonally fitted with POLYMET Run Flat inserts, with absolute “ZERO “ air, was driven through the grueling desert track of RAK with rubbles, dry crossings, having a number of obstacles such as natural ramps, steps formed in the wadi, ditches as well as gravel tracks with corrugations, covered a total distance of 69.14 km in 02:08:17 "none stop, attained an average speed of 32.3 Km/h meeting FINABEL agreement mandate - 2.3.2 b) travel off-road cross country for 2 hours at a speed of approximately 30 km/hr without the tire leaving the wheel rim or shredding.View All Products
Ballistic test on POLYMET run flat inserts 5 rounds of bullet from an AK 47 is fired direct to run flat insert to meet AGREEMENT NO. 20.A.5. of finebel which says Puncturing of the tyre is to be achieved by means of a firing 7.62mm round fired from a range of 50 metres; 5 rounds will be fired into the tyre wall and 2 into the tread area On close inception it can be noticed that there is no visible hole of the 7.62 mm slug and the run flat has not been cracked or brittle due to special combination of advanced polymer used in manufacturing them by POLYMET. First of its kind manufactured in the Middle east. meeting full FINABLE requirements.
As usual run flat insert market is also full of copies of products with spurious certificates. Most of these are bulk manufactured in world factories using recycled Nylon .There are difference in design and structure in the case of run flat inserts also. Any genuinely manufactured run flat insert will certified and tested and each run flat should be having manufacturer name printed on it with country of manufacturing
Runflat Tire Inserts System” Manufactured By Polymet Industries LLC
Wiz 06 Shed No 29 & 31
Rakia – Industrial Area
Ras Al Khaimah –
United Arab Emirates